Home > How To > How To Create Two Separate Networks

How To Create Two Separate Networks

Contents

I did get this working on an Asus RT3200 running the Merlin WRT firmware using IP aliasing and some convoluted NAT, but it isn't stable enough so now I'm hoping an Can I connect 2 Wireless Routers without cascading Connecting two routers, sharing internet connection of router A with router B while keeping networks A and B separate? Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site. P.S. weblink

If there's no IP on that subnet configured inside the cascaded router, then that subnet can't route back through to the gateway and onward IIUC, which leads back to the original Ideally you'll have a multi-nic router providing two separate LANs, but that's more expensive and complicated, so you could possibly justify the double NAT config. I even re-cramped the connectors 3 times to make sure I'm not swapping some wires. Computer restarts and crashes Three Word Game 2016 20v power on 19v laptop Off to a great start » Site Navigation » Forum> User CP> FAQ> Support.Me> Steam Error 118> 10.0.0.2> More Help

How To Create Two Separate Networks

This may or may not be the problem. I've also experimented with setting the secondary router to router and gateway modes, but I've had no luck with either. So I kindly ask if someone can help with this issue, I'm running out of ideas to test and I kinda need this to work soon-ish. I.e., what problem does using it solve?

However, it seems that both options on this ATT router for static IPs present problems - the "public subnet" creates double NAT problems and this "cascaded router" without ability to assign You may need to shrink your DHCP pool if it takes an entire subnet. E.g. Multiple Networks One Internet Connection So, the ATT router will be forwarding some /29 packets with a completely different start (like 162.24.15.X) to the 192.168.1.10 interface of the router, and it will then decode those and

So my question is, can the 20-25 meter ethernet cable between the routers (the distance might be few meters shorter, I can measure the distance precisely if needed) be too long The answer is "yes." Logically the switch, or router set to act a switch, is transparent. I mean, logically. this That's why I'm trying to assign a static IP because I have a gut feeling that the there is a problem with two routers together.

And a flip cable is a roll-over cable. Double Nat Showing results for  Search instead for  Did you mean:  AT&T Forums Home / Internet / AT&T Internet / AT&T Internet Equipment / Motorola NVG510 "Cascaded Router" Options Subscribe to RSS Feed Are you looking for the solution to your computer problem? Ok.

How To Setup 2 Networks With 1 Router

And so I don't know how to change the config on the second one. But I want strictly static IP addressing on the devices attached to the primary router. How To Create Two Separate Networks You earned the Liz badge! × Share this topic AT&T Internet Equipment AT&T Internet Internet Community Blog Community Home ATT.NET BUSINESS ABOUT AT&T FULL SITE PRIVACY TERMS OF USE CONTACT US One Internet Connection Two Private Lans If you're not already familiar with forums, watch our Welcome Guide to get started.

The Linksys is at 192.168.1.1, and its DHCP goes from 192.168.1.100 to 192.168.1.149. have a peek at these guys In the first router's web interface I can't see that the second one got an IP address on which I could connect. Any answers are very appreciated. On this one I disabled DHCP and it works well so that clients connected to the second router get an IP by the first one and have internet access. Cascading Routers Lan To Wan

All rights reserved. solved How to connect and have two separate networks with 1 modem and 2 routers? Just tried with a small crossover cable with both routers in my room and by the looks of it, the damn thing seems to work! http://realink.org/how-to/how-to-set-up-two-networks-with-one-router.html Afterwards I could connect to it and so I set the static IP address outside the DHCP range of the 1st router and disabled DHCP.

But I can't seem to figure out why can't i connect to the wireless printer from my Airport Extreme WIFI ?However, If i activate my Wireless Broadcaster from my Main Modem Turn off DHCP and set the IP to 192.168.1.2, make sure the subnet mask matches the main router. However the website says it does.

You probably want to use IP Passthrough for normal router-behind-NVG510 situations...

For a "more sophisticated routed," I assume you are referring to a commercial grade router? Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party. So..... I've just checked EACH pair of wires with a digital meter to check the conductivity, and they all seem to be working properly And to make it worse, shops are closed

Anyways, to make a long story short (I'm all hyped!), the setup works and I finally have a working two router cascaded network... As a junior member, I liked your forums very much: the interface is handy, the answers are very quick and intelligible. Also, should I use a LAN-WAN connection or a LAN-LAN connection? this content The big downside of cascading 2 routers is if you need to do any kind of port mapping or UPnP.

Normally this default gateway adress must be on the same subnet as the VLAN, so I can imagine this not working correctly - another manifestation of this strange cascaded router option...Any You put what I've just said in tech lingo. DHCP is enabled here. WAN and LAN IP of netgear, DHCP scope, DNS?

Evgeny9, Jan 7, 2010 #5 TerryNet Terry Moderator Joined: Mar 23, 2005 Messages: 72,813 Yes, I will answer your first question.